Flux du groupe

I have two of the Athom Garage Door Opener units. One was purchased about a year ago and has what seems like ESPHome firmware, and the other purchased more recently and seems to have HomeKit. I like the ESPHome firmware better as I seem to get more Control in Home Assistant. For example, I can stop the movement of the garage door mid-stream with the ESPHome Device, but cannot do so with the HomeKit flashed device. Would it be possible for me to flash the HomeKit device with the ESPHome firmware?

I recently tried to “take control” of my new PS02C3MZ presence senor in esphome dashboard and now everything is unknown.

How can I return this device to stock? T

My new presence sensor does not detect occupancy or PIR. The mmWave and LUX sensors does detect, but the other 2 sensors do not. I tried to send a message, but have not heard back and did not get a confirmation email.

Hi i just want to know what i do wrong, c3 moon module firmware just can get installed on the flim controller without failing.

I've performed a manual upgrade to WLED 0.15.0 on my LS-4P via the web interface and it seems to have gotten bricked.

There is no WLED access point, and it is not connecting to the configured wifi, popping the cover off and powering the device on and off also doesn't show any signs of life.

Is 0.15.0 not supported?

Is there a way to reset / recover the bricked device?

I see in https://www.athom.tech/blank-1/wled-gu10-rgbcw your comment:

"Open sources firmware has no control of power supply , if you maximum all channel at the same time, it will highly possible damage the bulb and we will not provide warranty in such case"

Do you have any advise on what I can reliably set the different channels to in each lamp to have run continuously without overheating? I want to output warm white light continuously - can I set each channel to 80%? Can you recommend a configuration that will give continuous warm light output?

I have purchased four of these globes to trial, and am considering replacing all globes in the house.

I have a custom home control system and use a MQTT broker on a Raspberry Pi, with tasmota wall switches publishing to an MQTT topic to turn on a set of lights that subscribe to that topic. Before installing…

Hello,

I have a SW11-ESP-2EU touch wall switch.

It is equiped with an SW-03-ESP8285 ESP chip.

I cannot flash it through web or OTA because I disabled OTA by mistake.

How can I flash it through USB ? I cannot find the pinout for VCC, GND, TX & RX

Thank you for your help

I am getting the attached error when i try to update to the latest version of ESPHome

In file included from /data/cache/platformio/packages/framework-arduinoespressif8266/libraries/ESP8266mDNS/src/ESP8266mDNS.h:48,
                 from /data/cache/platformio/packages/framework-arduinoespressif8266/libraries/ESP8266mDNS/src/ESP8266mDNS.cpp:23:
/data/cache/platformio/packages/framework-arduinoespressif8266/libraries/ESP8266mDNS/src/LEAmDNS.h:116:10: fatal error: WiFiUdp.h: No such file or directory

*****************************************************************
* Looking for WiFiUdp.h dependency? Check our library registry!
*
* CLI  > platformio lib search "header:WiFiUdp.h"
* Web  > https://registry.platformio.org/search?q=header:WiFiUdp.h
*
*****************************************************************

  116 | #include "WiFiUdp.h"
      |          ^~~~~~~~~~~
compilation terminated.
*** [.pioenvs/athom-presence-sensor-d93e72/lib3ff/ESP8266mDNS/ESP8266mDNS.cpp.o] Error 1

Processing facade-plug (board: esp8285; framework: arduino; platform: platformio/espressif8266@4.2.1)

--------------------------------------------------------------------------------

HARDWARE: ESP8266 80MHz, 80KB RAM, 1MB Flash

Dependency Graph

|-- ESPAsyncTCP @ 2.0.0

|-- ESP8266mDNS @ 1.2